Tuesday, October 29, 2019

Principles of Distillation Essay Example for Free

Principles of Distillation Essay What is distillation? Simply, distillation is the process in which a liquid is vaporized (turned to steam), recondensed (turned back into a liquid) and collected in a container. Nature uses a form of distillation to turn salt water (seawater) into fresh water (rain). Why do you use distillation to recycle waste solvents? Solvent-based waste contains volatile material (solvents) and non-volatile material (contaminants like paint, ink, grease, fiberglass, etc.). Many of the non-volatile contaminates are dissolved in the solvent (like salt dissolved in salt water) and cannot be filtered-out. Distillation is an ideal way to separate the two. Why is distillation an ideal way to separate the two? During the distillation process, the solvent-based waste is heated until it reaches the boiling point. It then evaporates (vaporizes) and passes through the condenser where heat is removed from the vapor and it turns back into a cool, clean reusable liquid (same process that causes dew to form). Fortunately, contaminates are typically not volatile (easily vaporized) and stay behind in the distillation tank. You say contaminates are typically not volatile, does this mean some are? Occasionally there are cases where a potential customer wishes to separate a volatile solvent from another volatile material. This is not the typical customer. Some cases include customers using an alcohol to remove water from parts to dry them or where they have solvent mixtures due to poor house keeping practices (they lump all waste solvents into one drum from different operations like painting and parts cleaning). To separate one volatile from another effectively requires fractional distillation; our process uses simple distillation. What are the differences between simple distillation and fractional distillation? Simply stated, in simple distillation, what you put in is what you get back, but it is free of non-volatile materials (it is clean!). Fractional distillation is much more complicated (and expensive). It is the base process where crude oil is turned into the many items that come from oil. Fractional distillation is not required for virtually all solvent recycling applica tions. What is vacuum distillation? Vacuum distillation is the distillation of a liquid under reduced pressure. The atmospheric pressure in the distillation tank is reduced making it possible to boil the liquid at a lower temperature. Liquids boil at lower temperatures under reduced pressure (the inverse is that a liquid boils at a higher temperature under pressure, which is why they use a pressure cap on an automobile radiator to increase the boiling point of the engine coolant to prevent boil-over). Why do you use vacuum distillation? Vacuum distillation is used to safely recover higher boiling point solvents. We limit the maximum temperature of the distillation unit’s heater. There is a temperature at which a flammable or combustible material can ignite by temperature only, this is called the autoignition temperature (this is discussed later). Some solvents boil at temperatures that exceed the temperature that the distillation heater can reach (392 º Fahrenheit). Vacuum distill ation lowers the boiling point to allow recovery within the heaters maximum setting. When do you use vacuum distillation? It is used to safely recover solvents with boiling points over 300 º Fahrenheit. Vacuum distillation should not be used on solvents with boiling points below 200 º Fahrenheit. If the maximum heater setting is 392 º Fahrenheit, why do I need to use vacuum distillation for solvents with boiling points over 300 º Fahrenheit, don’t you mean solvents with boiling points over 392 º Fahrenheit? No! When boiling a liquid, two factors come in to play. One is the requirement to have a â€Å"driving force† to force the liquid to boil and vaporize. This â€Å"driving force† is in the form of extra temperature to allow the solvent to develop a good rolling boil. The other factor is the role of the non-volatile residue. As you boil off solvent and the remaining mixture in the distillation tank becomes more concentrated in the nonvolatile material, the vapor pressure drops (Raoult’s Law) and most important, the boiling point goes up! So bottom line is that you need 50 to 100 degrees of extra temperature to do a good job of boiling the waste solvent. Also, the concentrated non-volatile material acts as an insulator towards the end of the process as it becomes more and more concentrated. So, as the percentage of non-volatiles in the contaminated solvent increases, the required heat to completely distill the mixture also increases. Sometimes solvents that have boiling points of 318 ºF (Xylene) may not require a vacuum if they are not highly contaminated but almost definitely would if the solid content was greater than, lets say 10%. Pulling a vacuum on such a mixture will reduce its boiling point and the overall time to process it. How is the vacuum created? The vacuum is generated using our JetVac technology. A stainless steel reservoir is primed once with clean solvent. A small stainless steel pump is immersed in the liquid and is attached to an explosionproof electric motor. When the motor is started, clean solvent is drawn into the pump and forced through a metal tube known as an aspirator. The aspirator looks like an open piece of pipe with a small orifice (hole) on one side. As the high velocity fluid is pumped across the face of the orifice, it creates suction (like a venturi on a carburetor). Air is pulled through the venturi from the distillation system and passes through a vent.

No comments:

Post a Comment

Note: Only a member of this blog may post a comment.